Grizzly Variable Speed Wood G0632 Bedienungsanleitung Seite 1

MODEL G063216" X 42" VARIABLE SPEED WOOD LATHEOWNER'S MANUAL(For models manufactured since 4/12)COPYRIGHT © APRIL, 2007 BY GRIZZLY INDU

-8-Model G0632 (Mfg. 4/12+)SafetyELECTRICAL EQUIPMENT INJURY RISKS. You can be shocked, burned, or killed by touching live electrical components or

Model G0632 (Mfg. 4/12+)-9-WEARING PROPER APPAREL. Do not wearclothing, apparel or jewelry that can becomeentangled in moving parts.

-10-Model G0632 (Mfg. 4/12+)Additional Safety for Wood LathesKEEPING GUARDS IN PLACE. Make sure all guards are in place and that the lathe sits

Model G0632 (Mfg. 4/12+)-11-Circuit RequirementsSECTION 2: POWER SUPPLYAvailabilityBefore installing the machine, consider the avail-ability and proxi

-12-Model G0632 (Mfg. 4/12+)Improper connection of the equipment-grounding wire can result in a risk of electric shock. The wire with green i

Model G0632 (Mfg. 4/12+)-13-SECTION 3: SETUPThis machine presents serious injury hazards to untrained users. Read through this entire manu-al to becom

-14-Model G0632 (Mfg. 4/12+)Box Inventory: (Figures 5–7) QtyA. Lathe Assembly—Headstock (mounted) ... 1—Tool Rest Base (m

Model G0632 (Mfg. 4/12+)-15-Clean UpSite ConsiderationsThe unpainted surfaces of your machine are coated with a heavy-duty rust preventativ

-16-Model G0632 (Mfg. 4/12+)Site ConsiderationsFigure 9. Minimum working clearances.220V, Single-Phase* 173/8"‡ 221/16"Motor* Footprint‡ Min

Model G0632 (Mfg. 4/12+)-17-AssemblyTo assemble your lathe:1. Stand the right and left supporting legs up approximately 47" apart, and

This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, r

-18-Model G0632 (Mfg. 4/12+)3. Secure the lathe assembly to the supporting legs with the (8) M10-1.5 x 25 cap screws and 10mm flat washers (s

Model G0632 (Mfg. 4/12+)-19 -Power ConnectionAfter you have completed all previous setup instructions and circuit requirements, the machine is r

-20-Model G0632 (Mfg. 4/12+)Before starting the lathe, make sure you have performed the preceding assembly and adjustment instructions, and you have r

Model G0632 (Mfg. 4/12+)-21-SECTION 4: OPERATIONSOperationsDamage to your eyes and lungs could result from using this machine without proper pro-tecti

-22-Model G0632 (Mfg. 4/12+)Adjusting HeadstockThe Model G0632 headstock can be positioned anywhere along the lathe bed and swiveled 360°.To pos

Model G0632 (Mfg. 4/12+)-23-Always operate the lathe with the headstock firmly locked to the bed. Otherwise, serious personal injury may occur.To swiv

-24-Model G0632 (Mfg. 4/12+)2. Re-engage the tool rest base lock handle to secure the tool rest assembly in position. Note: The large clamping hex n

Model G0632 (Mfg. 4/12+)-25-Installing/Removing Headstock CenterThe included spur center installs into the head-stock spindle with an MT#2 tape

-26-Model G0632 (Mfg. 4/12+)Installing/Removing Tailstock CenterThe included live center installs into the tailstock quill with an MT#2 tapered fit.To

Model G0632 (Mfg. 4/12+)-27-Headstock FaceplateTo mount a workpiece to the faceplate, refer to Faceplate Turning on Page 35.The faceplate ca

Table of ContentsINTRODUCTION ... 2Manual Accuracy ... 2Contact In

-28-Model G0632 (Mfg. 4/12+)Changing Speed RangesThe Model G0632 has two speed ranges: 1) the low range from 100 to 1200 RPM which provides a greater

Model G0632 (Mfg. 4/12+)-29-4. Use the motor tensioning handle to lift the motor assembly all the way up and re-tighten the motor mount cap sc

-30-Model G0632 (Mfg. 4/12+)IndexingFigure 37. Indexing pin and indexing holes.To use the indexing feature, place the indexing pin into one of the ind

Model G0632 (Mfg. 4/12+)-31-Selecting Turning ToolsLathe tools come in a variety of shapes and sizes, and usually fall into five major categories.• G

-32-Model G0632 (Mfg. 4/12+)Spindle TurningSpindle turning is the operation performed when a workpiece is mounted between the headstock and the

Model G0632 (Mfg. 4/12+)-33-1/4"Figure 44. Spur center properly embedded.7. With the workpiece still attached, insert the spur center into

-34-Model G0632 (Mfg. 4/12+)Spindle Turning Safety Tips:• When turning the lathe ON, stand away from the path of the spinning workpiece until

Model G0632 (Mfg. 4/12+)-35-Faceplate TurningFaceplate turning is when a workpiece is mounted to the faceplate, which is then mounted to the h

-36-Model G0632 (Mfg. 4/12+)Outboard TurningOutboard turning is a variation of faceplate turn-ing and is usually done when the stock diameter is gre

Model G0632 (Mfg. 4/12+)-37-SECTION 5: ACCESSORIESACCESSORIESG1194—3-Jaw ChuckA "must have" for the serious wood turner. This 3-jaw

-2-Model G0632 (Mfg. 4/12+)INTRODUCTIONWe are proud to offer this manual with your new machine! We've made every effort to be exact with

-38-Model G0632 (Mfg. 4/12+)SECTION 6: MAINTENANCEFor optimum performance from your machine, follow this maintenance schedule and refer to any sp

Model G0632 (Mfg. 4/12+)-39-Review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel-ops. If you nee

-40-Model G0632 (Mfg. 4/12+)SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTIONVibration noise while machine is running; noise changes when speed is changed.1.

Model G0632 (Mfg. 4/12+)-41-Aligning CentersAligning CentersTo ensure accurate and safe turning results, the headstock and tailstock centers must

-42-Model G0632 (Mfg. 4/12+)SHOCK HAZARD. Working on wiring that is con-nected to a power source is extremely dangerous. Touching electrified parts

Model G0632 (Mfg. Since 1/09+)-43-READ ELECTRICAL SAFETY ON PAGE 42!Electrical ComponentsFigure 58. Model G0632 control panel wiring (shown from the b

-44-Model G0632 (Mfg. Since 1/09+)READ ELECTRICAL SAFETY ON PAGE 42!Wiring Diagram OverviewHotHotGround6-15 Plug (As Recommended) G Bl Wt Gn Ground U2

Model G0632 (Mfg. Since 1/09+)-45-READ ELECTRICAL SAFETY ON PAGE 42!HotHotGround6-15 Plug (As Recommended) G Bl Wt Gn View this page in color at www.g

-46-Model G0632 (Mfg. 4/12+)Stand Breakdown1234V25566789101120-1121314151617171920212223242526272829SECTION 9: PARTS

Model G0632 (Mfg. 4/12+)-47-Stand Parts ListREF PART # DESCRIPTION REF PART # DESCRIPTION1 P0632001 SUPPORTING LEG 16 P0632016 TAILSTOCK LOCK HANDLE2

Model G0632 (Mfg. 4/12+)-3-Figure 1. Model G0632 component identification.IdentificationTo reduce the risk of serious injury when using this machine,

-48-Model G0632 (Mfg. 4/12+)Headstock Breakdown313233343536373839414244V244V2-144V2-244AV2434546304748495051535254555657585962606161-161-261-361-461-5

Model G0632 (Mfg. 4/12+)-49-Headstock Parts ListREF PART # DESCRIPTION REF PART # DESCRIPTION30 P0632030 COMPLETE HEADSTOCK ASSY 61-8 P0632061-8 FRONT

-50-Model G0632 (Mfg. 4/12+)Label PlacementSafety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintai

Model G0632 (Mfg. 4/12+)-51-Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of

CUT ALONG DOTTED LINEName _____________________________________________________________________________ Street ______________________________________

TAPE ALONG EDGES--PLEASE DO NOT STAPLEFOLD ALONG DOTTED LINEFOLD ALONG DOTTED LINEGRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069Place

Buy Direct and Save with Grizzly®– Trusted, Proven and a Great Value!~Since 1983~ORDER24 HOURS A DAY!1-800-523-4777Visit Our Website Today For Current

-4-Model G0632 (Mfg. 4/12+)Figure 2. Model G0632 headstock.MotorMotor Wiring Junction BoxSpindle HandwheelFrequency InverterSpindle LockFront Belt Acc

Model G0632 (Mfg. 4/12+)-5-The following is a list of common definitions, terms and phrases used throughout this manual as they relate to this wood la

-6-Model G0632 (Mfg. 4/12+)The information contained herein is deemed accurate as of 1/24/2013 and represents our most recent product specifications.D

Model G0632 (Mfg. 4/12+)-7-The information contained herein is deemed accurate as of 1/24/2013 and represents our most recent product specifications.D