Grizzly G0456 Bedienungsanleitung

MODEL G0456VARIABLE SPEED WOOD LATHEOWNER'S MANUALCOPYRIGHT © NOVEMBER, 2005 BY GRIZZLY INDUSTRIAL, INC. REVISED SEPTEMBER, 2007.WARNING: NO PORT

-8-G0456 Variable Speed Wood LatheAdditional Safety for Wood Lathes9. WORKPIECE CONDITION. Always inspect the condition of your workpiece. DO NOT

G0456 Variable Speed Wood Lathe-9-Serious personal injury could occur if you connect the machine to the power source before you have comple

-10-G0456 Variable Speed Wood LatheThe Model G0456 was carefully packed when it left our warehouse. If you discover the machine is damaged after

G0456 Variable Speed Wood Lathe-11-InventoryAfter all the parts have been removed from the crate, you should have the following items:Inventor

-12-G0456 Variable Speed Wood LatheFigure 4. Minimum working clearances.Floor LoadRefer to the Machine Data Sheet for the weight and footprint speci

G0456 Variable Speed Wood Lathe-13-Mounting LatheThe lathe bed and stand are separated for ship-ping safety purposes. We recommend positioning the sta

-14-G0456 Variable Speed Wood LatheSanding TableComponents and Hardware Needed: QtySanding Table ...

G0456 Variable Speed Wood Lathe-15-Figure 10. Dust hose attached to dust port.Dust CollectionRecommended CFM at Dust Port: 100 CFMDo not confuse t

-16-G0456 Variable Speed Wood LatheDamage to your eyes, lungs, and ears could result from using this machine without proper protective gear. A

G0456 Variable Speed Wood Lathe-17-The tailstock is equipped with a cam-action clamping system to secure it to the lathe bed. When the



-18-G0456 Variable Speed Wood LatheInstalling/Removing Spur CenterThe spur center installs in the headstock spindle with a taper fit.To prevent rustin

G0456 Variable Speed Wood Lathe-19-To remove the live center:1. Turn the handwheel counterclockwise until the tailstock quill bottoms out, c

-20-G0456 Variable Speed Wood LatheSelecting Turning ToolsLathe tools come in a variety of shapes and sizes and usually fall into five major categorie

G0456 Variable Speed Wood Lathe-21-Spindle turning (Figure 23) is the operation per-formed when a workpiece is mounted between the headstock and

-22-G0456 Variable Speed Wood Lathe9. Position the tool rest approximately 1⁄4" away from the workpiece and approximately 1⁄8" above t

G0456 Variable Speed Wood Lathe-23-4. Thread the faceplate onto the headstock spindle and tighten securely.Note: If screws cannot be placed in t

-24-G0456 Variable Speed Wood LatheThe disc sander accepts 12" diameter cloth or paper-backed PSA sanding discs, which are available

G0456 Variable Speed Wood Lathe-25-The most efficient way to get a perfect miter is to cut the workpiece slightly long and sand it to the desired dime

-26-G0456 Variable Speed Wood LatheSECTION 5: ACCESSORIESACCESSORIESG1194—3-Jaw ChuckA "must have" for the serious wood turner. This

G0456 Variable Speed Wood Lathe-27-Figure 38. Model H6542 Robert Sorby 8-PC Set.H6542—Robert Sorby HSS 8-PC Turning SetIf quality is king, then s

INTRODUCTION ... 2Foreword ... 2Contact Info ...

-28-G0456 Variable Speed Wood LatheFigure 42. Model H1223 woodturning book.H1223—Woodturning, A Foundation CourseKeith Rowley's best selling intr

G0456 Variable Speed Wood Lathe-29-Always disconnect power to the machine before performing maintenance. Failure to do this may result in serio

-30-G0456 Variable Speed Wood LatheReview the troubleshooting and procedures in this section to fix your machine if a problem develops. If you need re

G0456 Variable Speed Wood Lathe-31-SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTIONWorkpiece vibrates exces-sively.1. Workpiece mounted incorrectly.2. Workp

-32-G0456 Variable Speed Wood LatheA misaligned headstock will not give you accurate results and may be dangerous. This procedure takes approxim

G0456 Variable Speed Wood Lathe-33-A loose or damaged V-belt will not adequately transfer power from the motor to the spindle. This procedure

-34-G0456 Variable Speed Wood LatheThe Model G0456 features a DC motor, which uses heavy-duty carbon brushes. While these brushes are desi

G0456 Variable Speed Wood Lathe-35-When the table tilt is set to 0˚, the table should be adjusted perpendicular to the sanding disc face.Tools Needed

-36-G0456 Variable Speed Wood LatheFigure 54. Table aligned with sanding disc.1⁄16" Gap2. Align the table so that there is approximately a 1⁄16&

G0456 Variable Speed Wood Lathe-37-Electrical ComponentsPower CordMotor CordSpeed Sensor WireMotor Control BoardON/OFFPaddle SwitchDigital Display Cir

-2-G0456 Variable Speed Wood LatheIf you have any comments regarding this manual, please write to us at the address below:Grizzly Industrial, Inc.C/O

-38-G0456 Variable Speed Wood Lathe 

G0456 Variable Speed Wood Lathe-39-

-40-G0456 Variable Speed Wood LatheREF PART # DESCRIPTION REF PART # DESCRIPTION1 P0456001 BED 56 P0456056 HANDWHEEL HANDLE2 P0456002 CABINET STAND 57

G0456 Variable Speed Wood Lathe-41-Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the or

-42-G0456 Variable Speed Wood LatheGrizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the

 





G0456 Variable Speed Wood Lathe-3-The information contained herein is deemed accurate as of 10/17/2007 and represents our most recent product specific

-4-G0456 Variable Speed Wood LatheThe information contained herein is deemed accurate as of 10/11/2007 and represents our most recent product specific

G0456 Variable Speed Wood Lathe-5-Figure 1. Identification of main components.A. Miter GaugeB. 12" Sanding DiscC. HeadstockD. SpindleE. Spur

-6-G0456 Variable Speed Wood Lathe4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing dam

G0456 Variable Speed Wood Lathe-7-7. ONLY ALLOW TRAINED AND PROP-ERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instr