Grizzly G0459P Bedienungsanleitung

MODEL G0459/G0459P12" DRUM SANDEROWNER’S MANUALCOPYRIGHT © OCTOBER, 2005 BY GRIZZLY INDUSTRIAL, INC. REVISED MARCH, 2013 (TR)WARNING: NO PORTION

-8-Model G0459/G0459P (Mfg. 7/11+)ELECTRICAL EQUIPMENT INJURY RISKS. You can be shocked, burned, or killed by touching live electrical components or

Model G0459/G0459P (Mfg. 7/11+)-9-WEARING PROPER APPAREL. Do not wearclothing, apparel or jewelry that can becomeentangled in moving p

-10-Model G0459/G0459P (Mfg. 7/11+)Additional Safety for Drum SandersFEEDING STOCK. Do not stand in the direct path of a workpiece at the infeed

Model G0459/G0459P (Mfg. 7/11+)-11-SECTION 2: POWER SUPPLYAvailabilityBefore installing the machine, consider the avail-ability and proximity of the r

-12-Model G0459/G0459P (Mfg. 7/11+)Improper connection of the equipment-grounding wire can result in a risk of electric shock. The wire with

Model G0459/G0459P (Mfg. 7/11+)-13-SECTION 3: SETUPThe following are needed to complete the setup process, but are not included with your machin

-14-Model G0459/G0459P (Mfg. 7/11+)Site ConsiderationsFigure 4. Minimum working clearances.261/2"24"Weight LoadRefer to the Machine Data She

Model G0459/G0459P (Mfg. 7/11+)-15-MountingThe base of this machine has holes that allow it to be mounted to a workbench. We strongly

-16-Model G0459/G0459P (Mfg. 7/11+)To connect a dust collection hose:1. Remove the four Phillips head screws at the dust port hole.2. Place the 21

Model G0459/G0459P (Mfg. 7/11+)-17-Recommended AdjustmentsFor your convenience, the adjustments listed below have been performed at the fac

This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, r

-18-Model G0459/G0459P (Mfg. 7/11+)SECTION 4: OPERATIONSTo complete a typical operation, the operator does the following:1. Examines the workpiece

Model G0459/G0459P (Mfg. 7/11+)-19 -Basic ControlsRefer to Figure 11 and the following descriptions to become familiar with the basic controls of this

-20-Model G0459/G0459P (Mfg. 7/11+)Stock Inspection and RequirementsSome workpieces are not safe or may require modification before they are sa

Model G0459/G0459P (Mfg. 7/11+)-21-Depth of CutThe optimum depth of cut will vary based on the type of wood, feed rate, and sandpaper gr

-22-Model G0459/G0459P (Mfg. 7/11+)DO NOT sand more than one board at a time. Minor variations in thickness can cause one board to be propelled by the

Model G0459/G0459P (Mfg. 7/11+)-23-Paper ReplacementFigure 18. Sandpaper ends taped on Model G0459.4. Use the old sandpaper as a pattern to c

-24-Model G0459/G0459P (Mfg. 7/11+)SECTION 5: ACCESSORIESPRO-STICK® Sanding PadExtend the life of your sandpaper! Just feed this crepe-rubber cleanin

Model G0459/G0459P (Mfg. 7/11+)-25-Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious pers

-26-Model G0459/G0459P (Mfg. 7/11+)Failure to routinely inspect your drum sander for damage and wear could result in unsatis-factory work results, pre

Model G0459/G0459P (Mfg. 7/11+)-27-Symptom Possible Cause Possible SolutionMachine does not start or a breaker trips.1. Plug or receptacle is

Table of ContentsINTRODUCTION ... 2Manual Accuracy ... 2Contact In

-28-Model G0459/G0459P (Mfg. 7/11+)Symptom Possible Cause Possible SolutionMachine stalls or is underpowered.1. Dust collection ducting is at faul

Model G0459/G0459P (Mfg. 7/11+)-29-Symptom Possible Cause Possible SolutionShort V-belt lifespan.1. Pulleys not aligned correctly.2. Improperly te

-30-Model G0459/G0459P (Mfg. 7/11+)Tools Needed: QtyHex Wrench 6mm ... 1Wrench 12mm ...

Model G0459/G0459P (Mfg. 7/11+)-31-Removal/ReplacementReplace the V-belt if you notice fraying, cracking, glazing, or any other damage. A worn/d

-32-Model G0459/G0459P (Mfg. 7/11+)Tools Needed: QtyWrench 19mm ... 1Phillips Head Screwdriver #2 ...

Model G0459/G0459P (Mfg. 7/11+)-33-Tools Needed: QtyHex Wrench 4mm ... 1Wrench 19mm ...

-34-Model G0459/G0459P (Mfg. 7/11+)5. Raise the table until the gauge blocks just touch the bottom of the sanding drum. Note: A good way to

Model G0459/G0459P (Mfg. 7/11+)-35-However, you can only minimize snipe so much before the workpiece will slip or kick out, causing a hazard to

-36-Model G0459/G0459P (Mfg. 7/11+)Note: You may open the side covers to gain better access for the following adjustments. This is not required.6. Tu

Model G0459/G0459P (Mfg. 7/11+)-37-5. Loosen the chain by loosening the hex nut on the bottom of the idler roller sprocket shown in Figure 39.Figure

-2-Model G0459/G0459P (Mfg. 7/11+)INTRODUCTIONWe stand behind our machines. If you have any service questions, parts requests or general ques-tions ab

-38-Model G0459/G0459P (Mfg. 7/11+)Tools Needed: QtyHex Wrench 6mm ... 1Wrench/Socket 19mm ...

Model G0459/G0459P (Mfg. 7/11+)-39-Figure 43. Drum sander disassembled to Step 8.9. Remove the sanding drum (4 lock nuts and 4 flat washers) and V-be

-40-Model G0459/G0459P (Mfg. 7/11+)11. Mark the top of the table lift screws with arrows (all pointing in same direction) and mark the

Model G0459/G0459P (Mfg. 7/11+)-41-Figure 51. Conveyor belt removed from table.Conveyor Motor CoverConveyor MotorFlat WasherFlat WasherLeft Rear Rolle

-42-Model G0459/G0459P (Mfg. 7/11+)Figure 52. Helical gear and crank handle helical gear.34. Re-install and secure the brace. 35. Try moving the con

Model G0459/G0459P (Mfg. 7/11+)-43-SHOCK HAZARD. Working on wiring that is con-nected to a power source is extremely dangerous. Touching electrified

-44-Model G0459/G0459P (Mfg. 7/11+)READ ELECTRICAL SAFETY ON PAGE 43!Electrical ComponentsFigure 54. Feed motor.Figure 57. Capacitor.Figure 58. Variab

Model G0459/G0459P (Mfg. 7/11+)-45-READ ELECTRICAL SAFETY ON PAGE 43!ONOFFDRUM MOTORFEEDMOTORTHERMAL CIRCUIT BREAKERON/OFF SWITCHVARIABLE SPEED CONTRO

-46-Model G0459/G0459P (Mfg. 7/11+)FrameSECTION 9: PARTS12344555-15-166667-17-17-27-28-18-18-18-28-38-48-58-68-78-78-78-78-78-78-78-7910111516V2171819

Model G0459/G0459P (Mfg. 7/11+)-47-REF PART # DESCRIPTION REF PART # DESCRIPTION1 P0459001 FRAME 32V3 P0459P032V3 FRONT PANEL V3.01.112 PN02 HEX NUT 5

Model G0459/G0459P (Mfg. 7/11+)-3-Figure 1. Front view, Model G0459.IdentificationTop CoverCover Lock KnobDust PortCrank HandleDC Feed MotorThermal Ci

-48-Model G0459/G0459P (Mfg. 7/11+)172323252526262727427070717373737374747474818182828585858586868686888888888989898989-189-189-189-190909292-19498Dru

Model G0459/G0459P (Mfg. 7/11+)-49-1725353650-150-251V251-1V25258575758606061617474646465-1666977798039V439V4-139V4-239V4-339V4-539V4-639V4-739V4-739V

-50-Model G0459/G0459P (Mfg. 7/11+)20955212V2213214215216217218221222Label PlacementSafety labels warn about machine hazards and ways to prevent injur

CUT ALONG DOTTED LINEName _____________________________________________________________________________ Street ______________________________________

TAPE ALONG EDGES--PLEASE DO NOT STAPLEFOLD ALONG DOTTED LINEFOLD ALONG DOTTED LINEGRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069Place

WARRANTY AND RETURNSGrizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchas

Buy Direct and Save with Grizzly®– Trusted, Proven and a Great Value!~Since 1983~ORDER24 HOURS A DAY!1-800-523-4777Visit Our Website Today For Current

-4-Model G0459/G0459P (Mfg. 7/11+)The information contained herein is deemed accurate as of 4/1/2013 and represents our most recent product specificat

Model G0459/G0459P (Mfg. 7/11+)-5-The information contained herein is deemed accurate as of 4/1/2013 and represents our most recent product specificat

-6-Model G0459/G0459P (Mfg. 7/11+)The information contained herein is deemed accurate as of 4/1/2013 and represents our most recent product specificat

Model G0459/G0459P (Mfg. 7/11+)-7-The information contained herein is deemed accurate as of 4/1/2013 and represents our most recent product specificat