Grizzly G0459 Bedienungsanleitung

MODEL G045912" DRUM SANDEROWNER’S MANUALCOPYRIGHT © OCTOBER, 2005 BY GRIZZLY INDUSTRIAL, INC., REVISED MAY, 2007 (BL)WARNING: NO PORTION OF THIS

-8-G0459 12" Drum SanderAdditional Safety for Drum Sanders6. DUST COLLECTION SYSTEM. Never operate the sander without an adequate dust

G0459 12" Drum Sander-9-Figure 2. Typical type 5-15 plug and receptacle.Serious personal injury could occur if you connect the machine t

-10-G0459 12" Drum SanderThe Model G0459 was carefully packed when it left our warehouse. If you discover the machine is damaged after y

G0459 12" Drum Sander-11-InventoryAfter all the parts have been removed from the two boxes, you should have the following items:Box 1: (

-12-G0459 12" Drum SanderPlacing SanderTo place the sander in a permanent location:1. With an assistant's help, lift the sander out of the

G0459 12" Drum Sander-13-Installing Crank HandleComponents and Hardware Needed: QtyCrank Handle ...

-14-G0459 12" Drum SanderTest RunNow that the machine is connected to the power source, it is important to perform a test run to make su

G0459 12" Drum Sander-15-Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always

-16-G0459 12" Drum SanderVariable SpeedThe variable speed knob allows you to increase the feed rate from 0–15 FPM. The correct speed to use depen

G0459 12" Drum Sander-17-DO NOT sand more than one board at a time. Minor variations in thickness can cause one board to be propelled by the rapi

Safety Label PlacementThe safety labels on this machine warn and indicate how to protect the operator or bystander from machine hazards. The machine o

-18-G0459 12" Drum SanderPaper ReplacementFigure 12. Sandpaper ends taped on Model G0459.4. Use the old sandpaper as a pattern to cut ou

G0459 12" Drum Sander-19-SECTION 5: ACCESSORIESPRO-STICK® Sanding PadExtend the life of your sandpaper! Just feed this crepe-rubber cleaning pa

-20-G0459 12" Drum SanderG1163—1HP Dust CollectorEffective dust collection not only keeps your shop cleaner and more pleasant to work in, it can

G0459 12" Drum Sander-21-Always disconnect power to the machine before performing maintenance. Failure to do this may result in serious pe

-22-G0459 12" Drum SanderTable Lift Screws: These should be lubricated with lithium grease every six months. Clean the table lift screw

G0459 12" Drum Sander-23-SECTION 7: SERVICESymptom Possible Cause Possible SolutionMachine does not start or a breaker trips.1. Plug or recepta

-24-G0459 12" Drum SanderSymptom Possible Cause Possible SolutionMachine stalls or is underpowered.1. Dust collection ducting is at fault.2. Lo

G0459 12" Drum Sander-25-Symptom Possible Cause Possible SolutionShort V-belt lifes-pan.1. Pulleys not aligned correctly.2. Improperly tensioned.

-26-G0459 12" Drum SanderTools Needed: QtyHex Wrench 6mm ...1Wrench 12mm ...

G0459 12" Drum Sander-27-Removal/ReplacementReplace the V-belt if you notice fraying, cracking, glazing, or any other damage. A worn/damage

Table of ContentsINTRODUCTION ...

-28-G0459 12" Drum SanderTools Needed: QtyWrench 19mm ...1Phillips Head Screwdriver #2 ...

G0459 12" Drum Sander-29-Tools Needed: QtyHex Wrench 4mm ...1Wrench 19mm ...

-30-G0459 12" Drum Sander6. Lower the table one full turn of the crank han-dle. Wait until the chain starts moving before starting to count the

G0459 12" Drum Sander-31-However, you can only minimize snipe so much before the workpiece will slip or kick out, causing a hazard to the

-32-G0459 12" Drum SanderNote: You may open the side covers to gain better access for the following adjustments. This is not required.6. Turn

G0459 12" Drum Sander-33-5. Loosen the chain by loosening the hex nut on the bottom of the idler roller sprocket shown in Figure 38.Figure 37. M

-34-G0459 12" Drum SanderTools Needed: QtyHex Wrench 6mm ...1Wrench/Socket 19mm ...

G0459 12" Drum Sander-35-Figure 42. Drum sander disassembled to Step 8.9. Remove the sanding drum (4 lock nuts and 4 flat washers) and V-belt (F

-36-G0459 12" Drum Sander11. Mark the top of the table lift screws with arrows (all pointing in same direction) and mark the scr

G0459 12" Drum Sander-37-Figure 50. Conveyor belt removed from table.Figure 49. Rear left roller bracket loosened.20. Remove the conveyor motor

SECTION 7: SERVICE ... 23Troubleshooti

-38-G0459 12" Drum SanderFigure 51. Worm wheel and worm gear.35. Reinstall and secure the brace. 36. Try moving the conveyor table up and

G0459 12" Drum Sander-39-Electrical ComponentsVariable Speed Control, Circuit BoardFeed MotorSwitch Box WiringMotor WiringCapacitorVariable Speed

-40-G0459 12" Drum Sander 

G0459 12" Drum Sander-41-12344556669101213141516171718192021222428292929293132333440465457591001011031041071081091121131141151171181191191129298-

-42-G0459 12" Drum Sander92-1922782818586747388987073748827818586868582179442717073748888238989-19089-18926252586857473526965-1666474577464616051

G0459 12" Drum Sander-43-REF PART # DESCRIPTION REF PART # DESCRIPTION1 P0459001 FRAME 34 PN02 HEX NUT 5/16-182 PN02 HEX NUT 5/16-18 35 PN03 HEX

-44-G0459 12" Drum SanderREF PART # DESCRIPTION REF PART # DESCRIPTION100 P0459100 DUST SCOOP 113 P0459113 CRANK HANDLE101 P0459101 WORM GEAR SHA

G0459 12" Drum Sander-45-Safety Label Placement and Parts ListSafety Label PlacementThe safety labels on this machine warn and indicate how to pr

-46-G0459 12" Drum SanderGrizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date

CUT ALONG DOTTED LINEName _____________________________________________________________________________ Street ______________________________________

G0459 12" Drum Sander-3-If you have any comments regarding this manual, please write to us at the address below:Grizzly Industrial, Inc.C/O Techn

TAPE ALONG EDGES--PLEASE DO NOT STAPLEFOLD ALONG DOTTED LINEFOLD ALONG DOTTED LINEGRIZZLY INDUSTRIAL, INC.P.O. BOX 2069BELLINGHAM, WA 98227-2069Place

Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!-OR-• SECURE ORDERING• ORDERS SHIPPED WITHIN 24 HOURS• E-MAIL RESPONSE WITHIN O

-4-G0459 12" Drum Sander

G0459 12" Drum Sander-5-HFigure 1. Front view, Model G0459.A. Top CoverB. Cover Lock KnobC. Dust PortD. HandleE. Crank HandleF. Depth Scale

-6-G0459 12" Drum Sander4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause permanent hearing damage.

G0459 12" Drum Sander-7-7. ONLY ALLOW TRAINED AND PROP-ERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make sure operation instructio